Kontron COMe Starterkit Eval T2 Manual de usuario Pagina 112
- Pagina / 218
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
COM Express Interfaces
Carrier designers should not buffer LPC_CLK for maximum Module interoperability. The COM
Express specification intends for a single load on the clock but experience has shown that two
devices can be driven if both devices are within 2" of each other.
2.16.2.2. LPC Reset Signal
The LPC interface should use the signal 'CB_RESET#' as its reset input. This signal is issued by
the COM Express Module as a result of a low 'SYS_RESET#', a low 'PWR_OK' or a watchdog
timeout event. If there are multiple LPC devices implemented on the Carrier Board, it is
recommended to split the signal 'CB_RESET#' so that each LPC device will be provided with a
separate reset signal. Therefore a buffer circuit like the one shown in Figure 42 below should be
used.
Figure 42: LPC Reset Buffer Reference Circuitry
Note: The LPC Firmware Hub section has been moved to section 9 'Appendix A:
Deprecated Features' on page 203 below in this version of the Carrier Design
Guide. LPC Firmware hubs were typically used for Carrier based BIOS in
previous generation designs. A Carrier based BIOS is now typically support
on SPI. See section 2.17 'SPI – Serial Peripheral Interface Bus' on page 118
below for more information.
PICMG
®
COM Express
®
Carrier Board Design Guide Rev. 2.0 / December 6, 2013
112/218
VCC_3V3 VCC_3V3
CEX
CB_RESET#
IO_RST#
FWH_RST#
C174
100n
C174
100n
U2D
74LVX125T
U2D
74LVX125T
OE#
13
IN
12
VCC
14
GND
7
OUT
11
U2C
74LVX125T
U2C
74LVX125T
OE#
10
IN
9
VCC
14
GND
7
OUT
8
- COM Express® 1
- Carrier Design Guide 1
- Contents 3
- 1. Preface 8
- 1.6. Name and logo usage 9
- 1.7. Intellectual property 10
- Term Description 11
- 1.10. Schematic Conventions 15
- 2. COM Express Interfaces 16
- COM Expre ss Module 17
- Type 10 17
- Table 4: Pin-out Comparison 20
- , the PCI 30
- 2.3.5. Schematic Examples 34
- Signal Pin Description I/O 45
- Figure 15: ExpressCard Size 45
- 2.4.1. Signal Definitions 48
- 2.4.2. PEG Configuration 49
- 2.4.3. Reference Schematics 52
- DisplayPort is supported 55
- DisplayPort Example 56
- Figure 21: HDMI Example 57
- Figure 22: DVI Example 59
- SDVO Port Configuration 61
- Supported SDVO Devices 62
- DVI_SDAROM 63
- DVI_SCLROM 63
- SDVO I2C Bus Address 63
- Write = 0111 0000 (70h) 63
- Read = 0111 0001 (71h) 63
- 2.6.1. Signal Definitions 66
- Earliest asserted 1ms after 68
- 3.3V, 5V and 12V are stable 68
- 2.7. LAN 70
- 2.7.2. Reference Schematics 73
- 2.8. USB Ports 76
- 2.8.2. Reference Schematics 77
- 2.9. USB 3.0 81
- 2.9.1.3. USB 3.0 connector 83
- 2.9.2. Reference Schematics 84
- 2.10. SATA 87
- Pins Signal Description 88
- SATA Port 89
- 2.11. LVDS 91
- Term Definition 94
- 2.11.2. Reference Schematics 97
- 2.12.1. Signal Definitions 99
- 2.12.2. Reference Schematics 100
- 2.13. VGA 101
- COM Express Interfaces 102
- 2.14. TV-Out 104
- COM Express Module 106
- AUDIO POWER 107
- AUDIO CODEC - ALC888 107
- ANALOG I/O CONNECTOR 107
- 2.15.1.2. AC'97 108
- Figure 41: Audio Amplifier 109
- 2.16.1. Signal Definition 111
- SUPER I/O 115
- COM1/COM2 116
- 2.17.1. Signal Definition 118
- 2.18.1. Signal Definitions 121
- 2.18.2. Reference Schematics 121
- 2.19.1. Signal Definitions 123
- 2.20.1. Signal Definitions 125
- C O M 1 C O M 2 126
- 2.21. CAN Interface 127
- 2.21.2. Reference Schematics 128
- 2.22. Miscellaneous Signals 129
- POWER ATX 133
- POWER AT 133
- Type 2 Detection 133
- 2.22.5. Watchdog Timer 137
- G P IO C o n n e c t o r 141
- 2.22.8. Fan Connector 142
- 2.22.9. Thermal Interface 143
- 2.23. PCI Bus 147
- 2.23.2. Reference Schematics 148
- 2.24.1. Signal Definitions 153
- 3. Power and Reset 156
- 3.2.1. ATX vs AT Supplies 157
- 3.2.2. Power States 157
- Power and Reset 158
- 3.2.5. Power Button 162
- 3.4. Reference Schematics 164
- Table 55: ATX Signal Names 166
- ATX Signal Name Description 166
- 3.5. Routing Considerations 167
- 3.5.3. VCC5_SBY Routing 168
- 4. BIOS Considerations 170
- Type Height Partnumber Note 171
- COM Express Module Connectors 172
- GND Plane 173
- Power Plane 173
- COM Express 175
- Table 60: Trace Parameters 176
- Symbol Definition 176
- Carrier Board 178
- Parameter Trace Routing 183
- Extended 194
- 7.2. Heatspreader 195
- (Ø2.7mm bore hole) 196
- (M2.5 thread) 196
- (Ø2.7 bore hole) 197
- Mechanical Considerations 198
- 8.3. Useful books 202
- 9.1. TV-Out 203
- 9.1.5. Signal Termination 206
- 9.1.6. Video Filter 206
- 9.1.7. ESD Protection 206
- 9.2. LPC Firmware Hub 207
- Appendix C: List of Tables 213
- Appendix D: List of Figures 215
- Table 79: Revision History 217
- Revision Date Author Changes 217
Relacionado con productos y manuales para Hardware Kontron COMe Starterkit Eval T2
Hardware Kontron COMe-bP5020 Manual de usuario
(71 paginas)
(71 paginas)
Hardware Kontron COMe-cP2020 Manual de usuario
(106 paginas)
(106 paginas)
Hardware Kontron COMe-mSP1 Manual de usuario
(97 paginas)
(97 paginas)
Hardware Kontron COMe-mTT10 Manual de usuario
(94 paginas)
(94 paginas)
Hardware Kontron COMe-mCT10 Manual de usuario
(100 paginas)
(100 paginas)
Hardware Kontron COMe-mBT10 Manual de usuario
(87 paginas)
(87 paginas)
Hardware Kontron COMe-cXLi2 Manual de usuario
(106 paginas)
(106 paginas)
Hardware Kontron COMe-cSP2 Manual de usuario
(109 paginas)
(109 paginas)
Hardware Kontron COMe-cPC2 Manual de usuario
(107 paginas)
(107 paginas)
Hardware Kontron COMe-cDC2 Manual de usuario
(97 paginas)
(97 paginas)
Hardware Kontron COMe-cPV2(v1.4) Manual de usuario
(123 paginas)
(123 paginas)
Hardware Kontron COMe-cPV2(v1.0) Manual de usuario
(122 paginas)
(122 paginas)
Hardware Kontron COMe-cOHXX Manual de usuario
(168 paginas)
(168 paginas)
Hardware Kontron COMe-cCT6 Manual de usuario
(110 paginas)
(110 paginas)
Hardware Kontron COMe-cTH6 Manual de usuario
(83 paginas)
(83 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales