Kontron AT890X Full-Size CLI Manual de usuario Pagina 132
- Pagina / 304
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Routing Commands AT8901/2/3
AT8901/2/3 CLI Reference Manual Page 3 - 20
3.5.6.1 no ip vrrp priority
This command sets the default priority value for the virtual router configured on a
specified interface.
Format
no ip vrrp <vrid> priority
Mode Interface Config
3.5.7 ip vrrp timers advertise
This command sets the frequency, in seconds, that an interface on the specified virtual
router sends a virtual router advertisement.
Default 1
Format
ip vrrp <vrid> timers advertise <1-255>
Mode Interface Config
3.5.7.1 no ip vrrp timers advertise
This command sets the default virtual router advertisement value for an interface.
Format
no ip vrrp <vrid> timers advertise
Mode Interface Config
3.5.8 show ip vrrp interface stats
This command displays the statistical information about each virtual router configured
on the FASTPATH switch.
Format
show ip vrrp interface stats <unit/slot/port> <vrid>
Modes Privileged EXEC
User EXEC
Uptime The time that the virtual router has been up, in days, hours, minutes
and seconds.
Protocol Represents the protocol configured on the interface.
State Transitioned to Master Represents the total number of times virtual router
state has changed to MASTER.
Advertisement Received Represents the total number of VRRP advertisements
received by this virtual router.
Advertisement Interval Errors Represents the total number of VRRP advertise-
ments received for which advertisement interval is different than the
configured value for this virtual router.
Authentication Failure Represents the total number of VRRP packets received that
don't pass the authentication check.
IP TTL errors Represents the total number of VRRP packets received by the virtual
router with IP TTL (time to live) not equal to 255.
Zero Priority Packets Received Represents the total number of VRRP packets
received by virtual router with a priority of '0'.
- AdvancedTCA 1
- AT8901/2/3 Preface 2
- Preface AT8901/2/3 4
- AT8901/2/3 10
- Appendix 24
- 1.1 Command Syntax 26
- 1.2 Command Conventions 26
- 1.2.1 Common Parameter Values 27
- 1.5 Command Modes 29
- 1.5.2 CLI Error Messages 32
- 1.6 Using CLI Help 33
- 1.7 Accessing the CLI 34
- Switching Commands 35
- 2. Switching Commands 36
- Switching Commands AT8901/2/3 100
- AT8901/2/3 Switching Commands 101
- Routing Commands 113
- Chapter 1 113
- 3. Routing Commands 114
- AT8901/2/3 Routing Commands 115
- Routing Commands AT8901/2/3 116
- Quality of Service Commands 167
- 4.1.4 classofservice trust 169
- 4.1.5 cos-queue min-bandwidth 170
- 4.1.6 cos-queue strict 170
- 4.1.6.1 no cos-queue strict 170
- 4.1.7 traffic-shape 171
- 4.1.7.1 no traffic-shape 171
- Mode Privileged EXEC 172
- [<unit/slot/port>] 172
- 4.3 DiffServ Class Commands 174
- 4.3.1.1 no class-map 175
- 4.3.2 class-map rename 175
- 4.3.3 match ethertype 175
- 4.3.4 match any 175
- 4.3.5 match class-map 175
- 4.3.5.1 no match class-map 176
- 4.3.6 match cos 176
- 4.3.7 match secondary-cos 176
- 4.3.9 match dstip 177
- 4.3.10 match dstl4port 177
- 4.3.11 match ip dscp 177
- 4.3.12 match ip precedence 178
- 4.3.13 match ip tos 178
- 4.3.14 match protocol 178
- 4.3.16 match srcip 179
- 4.3.17 match srcl4port 179
- 4.4 DiffServ Policy Commands 180
- 4.4.1 assign-queue 181
- 4.4.2 drop 181
- 4.4.3 mirror 181
- 4.4.4 redirect 181
- 4.4.5 conform-color 181
- 4.4.6 class 182
- 4.4.6.1 no class 182
- 4.4.7 mark cos 182
- 4.4.8 mark ip-dscp 182
- 4.4.9 mark ip-precedence 183
- 4.4.10 police-simple 183
- 4.4.11 policy-map 183
- 4.5 DiffServ Service Commands 184
- 4.6 DiffServ Show Commands 185
- 4.6.2 show diffserv 186
- 4.6.3 show policy-map 186
- 4.6.4 show diffserv service 188
- 4.6.7 show service-policy 189
- 4.7.3 {deny 191
- 4.7.4 mac access-group 192
- 4.7.4.1 no mac access-group 192
- 4.7.5 show mac access-lists 192
- 4.8.1 access-list 193
- 4.8.1.1 no access-list 195
- 4.8.2 ip access-group 195
- 4.8.2.1 no ip access-group 195
- 4.8.3 acl-trapflags 195
- 4.8.3.1 no acl-trapflags 196
- 4.8.4 show ip access-lists 196
- 4.8.5 show access-lists 197
- Utility Commands 199
- 5. Utility Commands 200
- AT8901/2/3 Utility Commands 201
- Utility Commands AT8901/2/3 202
- Management Commands 243
- 6. Management Commands 244
- 6.1.3 serviceport protocol 245
- 6.1.4 network parms 245
- 6.1.5 network protocol 245
- 6.1.6 network mac-address 245
- 6.1.7 network mac-type 245
- 6.1.7.1 no network mac-type 246
- 6.1.8 network javamode 246
- 6.1.8.1 no network javamode 246
- 6.1.9 show network 246
- 6.1.10 show serviceport 247
- 6.2.1 configuration 247
- 6.3 Telnet Commands 249
- 6.3.3 transport input telnet 250
- 6.3.4 transport output telnet 250
- 6.3.5 session-limit 250
- 6.3.8.1 no telnetcon timeout 252
- 6.3.9 disconnect 252
- 6.3.10 show telnet 252
- 6.3.11 show telnetcon 252
- 6.4.1 ip ssh 253
- 6.4.1.1 no ip ssh 253
- 6.4.2 ip ssh protocol 253
- 6.4.3 ip ssh server enable 253
- 6.5 User Account Commands 255
- 6.5.3 users snmpv3 accessmode 256
- 6.5.2.1 no users passwd 256
- 6.5.5 users snmpv3 encryption 257
- 6.5.6 show loginsession 257
- 6.6 SNMP Commands 258
- 6.6.3 snmp-server community 259
- 6.6.15 snmptrap 263
- 6.6.15.1 no snmptrap 263
- 6.6.16 snmptrap snmpversion 263
- 6.6.17 snmptrap ipaddr 263
- 6.6.21 show snmpbind 265
- 6.6.22 show snmpcommunity 265
- 6.6.23 show snmptrap 265
- 6.6.24 show trapflags 266
- 6.8 RADIUS Commands 267
- 6.8.2.1 no radius server host 268
- 6.8.3 radius server key 268
- 6.8.4 radius server msgauth 268
- 6.8.5 radius server primary 269
- 6.8.7 radius server timeout 269
- 6.8.8 show radius 270
- 6.8.9 show radius accounting 270
- 6.8.10 show radius statistics 271
- 6.9 TACACS+ Commands 272
- 6.10.1 script apply 275
- 6.10.3 script delete 276
- 6.10.4 script list 276
- 6.10.5 script show 276
- 6.10.6 script validate 276
- 6.12 Watchdog support 277
- 6.13 ASI commands 278
- Getting Help 279
- A. Getting Help 280
- AT8901/2/3 Getting Help 281
- Getting Help AT8901/2/3 282
- (if not under warranty) 283
- List of Commands 285
- B. List of Commands 286
- AT8901/2/3 List of Commands 287
- List of Commands AT8901/2/3 288
Relacionado con productos y manuales para Hardware Kontron AT890X Full-Size CLI
(9 paginas)
Hardware Kontron AT8901 Manual de usuario
(79 paginas)
(79 paginas)
Hardware Kontron AT8901M Manual de usuario
(76 paginas)
(76 paginas)
Hardware Kontron AT8901M CLI Manual de usuario
(313 paginas)
(313 paginas)
Hardware Kontron AT8902 Full Size CLI Manual de usuario
(304 paginas)
(304 paginas)
Hardware Kontron AT8902 Manual de usuario
(94 paginas)
(94 paginas)
Hardware Kontron AT8902M Manual de usuario
(92 paginas)
(92 paginas)
Hardware Kontron AT8902M CLI Manual de usuario
(315 paginas)
(315 paginas)
Hardware Kontron AT8904 Manual de usuario
(93 paginas)
(93 paginas)
Hardware Kontron AT8904 CLI Manual de usuario
(317 paginas)
(317 paginas)
Hardware Kontron AT8940 Manual de usuario
(84 paginas)
(84 paginas)
Hardware Kontron RTM8940 Manual de usuario
(36 paginas)
(36 paginas)
Hardware Kontron AT8402 CLI Manual de usuario
(253 paginas)
(253 paginas)
Hardware Kontron AT8404 Manual de usuario
(132 paginas)
(132 paginas)
Hardware Kontron AT8404 CLI Manual de usuario
(373 paginas)
(373 paginas)
Hardware Kontron RTM8050 Manual de usuario
(37 paginas)
(37 paginas)
Hardware Kontron AT8050 Manual de usuario
(165 paginas)
(165 paginas)
Hardware Kontron RTM8242 Manual de usuario
(34 paginas)
(34 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales