Kontron AT8404 CLI Manual de usuario Pagina 39
- Pagina / 373
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT8404 Switching Commands
Page 2 - 3 AT8404 CLI Reference Manual
2.1.1 interface
This command gives you access to the Interface Config mode, which allows you to enable or modify the operation
of an interface (port).
2.1.2 auto-negotiate
This command enables automatic negotiation on a port.
2.1.2.1 no auto-negotiate
This command disables automatic negotiation on a port.
2.1.3 auto-negotiate all
This command enables automatic negotiation on all ports.
2.1.3.1 no auto-negotiate all
This command disables automatic negotiation on all ports.
2.1.4 advertise speed
This command sets auto-negotiation advertised speed parameters. If full/half-duplex is not specified the speed is
valid for both modes.
Format interface <slot/port>
Mode Global Config
Default enabled
Format auto-negotiate
Mode Interface Config
Note: Automatic sensing is disabled when automatic negotiation is disabled.
Format no auto-negotiate
Mode Interface Config
Default enabled
Format auto-negotiate all
Mode Global Config
Format no auto-negotiate all
Mode Global Config
Format advertise speed <1000 | 100 | 10> [<half-duplex | full-duplex>]
Mode Interface Config
- AT8404 CLI Reference Manual 1
- AdvancedTCA 1
- Revision History 2
- Disclaimer 2
- AT8404 Preface 3
- About This Book 3
- Proprietary Note 3
- Trademarks 3
- Preface AT8404 4
- Explanation of Symbols 4
- For Your Safety 4
- Two Year Warranty 5
- Appendix 25
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.3 Common Parameter Values 29
- 1.6 FASTPATH Modules 30
- 1.7 Command Modes 31
- 1.9 CLI Error Messages 33
- 1.11 Using CLI Help 34
- 1.12 Accessing the CLI 34
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8404 100
- AT8404 Switching Commands 101
- Quality of Service Commands 175
- Chapter 1 175
- -mapping 176
- 3.1.3 classofservice trust 177
- 3.1.4 cos-queue min-bandwidth 177
- 3.1.13 show packet-memory 180
- 3.1.16 show protection-group 181
- Mode Global Config 183
- 3.3.1 class-map 184
- 3.3.1.1 no class-map 184
- 3.3.2 class-map rename 184
- 3.3.3 match ethertype 184
- 3.3.4 match any 185
- 3.3.5 match class-map 185
- 3.3.5.1 no match class-map 186
- 3.3.6 match cos 186
- 3.3.7 match secondary-cos 186
- 3.3.9 match dstip 187
- 3.3.10 match dstip6 187
- 3.3.11 match dstl4port 187
- 3.3.12 match ip dscp 187
- 3.3.13 match ip precedence 188
- 3.3.14 match ip tos 188
- 3.3.15 match protocol 189
- 3.3.17 match srcip 189
- 3.3.18 match srcip6 190
- 3.3.19 match srcl4port 190
- 3.3.20 match vlan 190
- 3.3.21 match secondary-vlan 190
- 3.4 DiffServ Policy Commands 191
- 3.4.4 redirect 192
- 3.4.5 conform-color 192
- 3.4.6 class 192
- 3.4.6.1 no class 193
- 3.4.7 mark cos 193
- 3.4.8 mark ip-precedence 193
- 3.4.9 police-simple 194
- 3.4.10 policy-map 194
- 3.4.10.1 no policy-map 194
- 3.5 DiffServ Service Commands 195
- 3.6 DiffServ Show Commands 196
- Mode Privileged EXEC 197
- <slot/port> in 199
- 3.6.7 show service-policy 200
- 3.7.4 mac access-group 203
- 3.7.4.1 no mac access-group 203
- 3.7.5 show mac access-lists 203
- 3.8.1 access-list 204
- 3.8.1.1 no access-list 205
- 3.8.2 ip access-list 205
- 3.8.2.1 no ip access-list 206
- 3.8.3 ip access-list rename 206
- 3.8.5 ip access-group 207
- 3.8.5.1 no ip access-group 207
- 3.8.6 acl-trapflags 207
- 3.8.6.1 no acl-trapflags 207
- 3.8.7 show acl-traptimer 208
- 3.8.8 acl-traptimer 208
- 3.8.8.1 no acl-traptimer 208
- 3.8.9 show ip access-lists 208
- 3.8.10 show access-lists 209
- 3.9.1 ipv6 access-list 209
- 3.9.1.1 no ipv6 access-list 210
- 3.9.2 ipv6 access-list rename 210
- 3.9.3 {deny 210
- 3.9.4 ipv6 traffic-filter 211
- 3.9.5 show ipv6 access-lists 211
- 3.10.1 auto-voip all 212
- 3.10.1.1 no auto-voip all 212
- 3.10.2 auto-voip 213
- 3.10.2.1 no auto-voip 213
- 3.10.3 show auto-voip 213
- Utility Commands 215
- 4. Utility Commands 216
- AT8404 Utility Commands 217
- Utility Commands AT8404 218
- Management Commands 277
- 5. Management Commands 278
- AT8404 Management Commands 279
- Management Commands AT8404 280
- Getting Help 329
- A. Getting Help 330
- AT8404 Getting Help 331
- FASTPATH log messages 334
- B. FASTPATH Log Messages 335
- AT8404 FASTPATH log messages 336
- FASTPATH log messages AT8404 337
- List of Commands 350
- C. List of Commands 351
- .......3 - 9 352
- List of Commands AT8404 353
- AT8404 List of Commands 354
Relacionado con productos y manuales para Hardware Kontron AT8404 CLI
Hardware Kontron RTM8050 Manual de usuario
(37 paginas)
(37 paginas)
Hardware Kontron AT8050 Manual de usuario
(165 paginas)
(165 paginas)
Hardware Kontron RTM8242 Manual de usuario
(34 paginas)
(34 paginas)
Hardware Kontron AT8242 Manual de usuario
(109 paginas)
(109 paginas)
Hardware Kontron AT8060 Manual de usuario
(160 paginas)
(160 paginas)
Hardware Kontron RTM806x Manual de usuario
(40 paginas)
(40 paginas)
Hardware Kontron 820152 DC-DC Manual de usuario
(4 paginas)
(4 paginas)
Hardware Kontron 820153 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
Hardware Kontron 820155 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
Hardware Kontron KT965 Series Manual de usuario
(90 paginas)
(90 paginas)
Hardware Kontron KTGM45-mITX Manual de usuario
(101 paginas)
(101 paginas)
Hardware Kontron KTQ45-FLEX Manual de usuario
(92 paginas)
(92 paginas)
Hardware Kontron KTQM67-mITX Manual de usuario
(148 paginas)
(148 paginas)
Hardware Kontron KTQ67-FLEX Manual de usuario
(137 paginas)
(137 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales