Kontron NSC2U IP Network Server Manual de usuario Pagina 125
- Pagina / 152
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Kontron IP Network Server NSC2U
December 2009 Product Guide, rev. 1.4
125
6.4 Clearing the Password
If the user or administrator password(s) is lost or forgotten, moving the password clear
jumper into the “clear” position clears both passwords. The password clear jumper
must be restored to its original position before a new password(s) can be set. The
password clear jumper (J1D2) is shown in Figure 17, “Recovery Jumper Blocks (J1D1,
J1D2, J1D3)” on page 33.
1. Power down the system and disconnect the power.
2. Open the server chassis. See Section 3.2.1, “Removing the Chassis Cover” for
instructions.
3. Move the jumper (J1D2) from the normal operation position, Password Clear
Protect, at pins 1 and 2 to the Password Clear Erase position, covering pins 2 and 3.
4. Reconnect the power, power up the system.
5. Power down the system and disconnect the power cord.
6. Return the Password Clear jumper (J1D2) to the Password Clear Protect position,
covering pins 1 and 2.
7. Close the server chassis. See Section 3.2.2, “Installing the Chassis Cover” for
instructions.
8. Reconnect the power and power up the server.
6.5 BMC Force Update Procedure
When performing a standard BMC firmware update procedure, the update utility places
the BMC into an update mode to allow the firmware to load safely onto the flash device.
In the unlikely event that the BMC firmware update process fails because the BMC is
not in the proper update state, the server board provides a BMC Force Update jumper
that can force the BMC into the proper update state. Use the following procedure if the
standard BMC firmware update process fails.
Once the firmware update process completes successfully, the firmware update utility
may generate an error stating that the BMC is still in update mode. Use the following
procedure to get out of Update mode:
1. Power down and remove the power cord.
2. Open the server chassis (remove the top cover).
3. Locate jumper block J1D1 and move the jumper to the Enable position (pins 2-3).
4. Close the server chassis.
5. Reconnect the power and restart the system.
Now perform the standard BMC firmware update procedure as documented in the
README.TXT file included in the BMC Firmware Update package.
Note: Normal BMC functionality is disabled when the Force BMC Update jumper is populated.
The server should never be run with the BMC Force Update jumper populated and this
header should only be used when the standard firmware update process fails. This
header should remain unpopulated by default when the server is running normally.
6. When the update has finished, power down the system and remove the power cord.
7. Open the server chassis (remove the top cover).
8. Close the server chassis.
9. Reconnect the power and restart the system.
10. Locate jumper block J1D1 and move the jumper to the Disable position (pins 1-2).
- Product Guide 1
- Rev. 1.4 1
- Legal Lines and Disclaimers 2
- Contents 3
- NSC2U Server—Contents 4
- Revision History 7
- NSC2U Server—Revision History 8
- 1 Introduction 9
- 1.3 Product Accessories 10
- Introduction—NSC2U Server 11
- 2Features 12
- 2.1 Server Components 14
- 2.2 NSC2U Server Back Panel 15
- 2.3 NSC2U Server Front Panel 15
- TS000112 17
- 2.5.1 SFP Board Features 18
- Features—NSC2U Server 19
- 2.9 Power Supply 21
- 2.10 System Cooling 21
- 2.10.3 PCI Cooling Area 22
- 2.10.5 Fan Speed Control 23
- 2.10.6 Cooling Summary 23
- 2.11 Hardware Requirements 24
- 3.1 Before You Begin 25
- TS000543 26
- TS000272 27
- TS000544 28
- TS000274 29
- TS000219 30
- AF000810 30
- TS000275 31
- AC PS DC PS 32
- 3.4.1.1 Configuration Jumpers 33
- 3.4.1.2 BIOS Select Jumper 33
- 3.4.2.1 Memory RASUM Features 36
- 3.4.2.2 Supported Memory 36
- TS000300 40
- 3.4.3 Installing DIMMs 41
- Branch 0 42
- Branch 1 42
- 3.4.5.2 Removing a Processor 44
- AF000768 45
- AF000770 46
- AF000771 46
- AF000772 47
- 4.1 Before You Begin 50
- 4.2.1 Riser Card Options 52
- TS000545 53
- TS000280 54
- Full-height Add-in Cards 55
- TS000546 56
- 4.4 Installing Intel 57
- Remote Management Modules 57
- GCM3 ModuleRMM Module 58
- TS000320 59
- TS000319 60
- TS000550 61
- TS000551 62
- TS000552 63
- TS000328 64
- TS000327 64
- TS000329 65
- TS000511 66
- TS000512 67
- TS000513 68
- TS000514 69
- TS000515 70
- TS000516 71
- TS000517 72
- TS000518 73
- TS000519 74
- Figure 59 75
- TS000521 76
- TS000522 77
- TS000523 78
- TS000524 79
- TS000525 80
- TS000526 80
- TS000527 81
- TS000528 82
- TS000529 83
- TS000530 84
- 4.6.4 Re-assemble the System 85
- TS000532 86
- TS000533 87
- TS000534 88
- TS000535 89
- TS000536 90
- TS000502 91
- TS000503 92
- TS000284 93
- TS000301 94
- TS000302 94
- TS000303 95
- TS000554 96
- TS000555 97
- 5.1 Before You Begin 98
- TS000556 99
- 5.2.1 Removing the CPU Fans 100
- 5.2.2 Replacing the CPU Fans 101
- NSC2U Server—5 102
- TS000560 103
- TS000562 105
- TS000564 107
- TS000565 108
- TS000566 109
- Backplane Board 110
- TS000313 111
- Assembly 112
- TS000316 113
- TS000568 115
- TS000569 116
- TS000570 118
- TS000537 119
- TS000308 121
- 6 Server Utilities 122
- 6.2 Upgrading the BIOS 123
- 6.2.1.2 Obtaining the Upgrade 124
- 6.3 Clearing the CMOS 124
- 6.4 Clearing the Password 125
- 7 Troubleshooting 126
- NSC2U Server—7 128
- 7.5 LED Information 131
- 7.6 BIOS Error Messages 132
- 7.6.1 BIOS POST Beep Codes 133
- 8 Warranty 135
- NSC2U Server—8 136
- A.1 Emissions Disclaimer 137
- A.2 Intended Uses 137
- NSC2U Server—A 138
- A.3 Safety Cautions 139
- Wichtige Sicherheitshinweise 140
- Consignes de sécurité 142
- Information en 144
- B.2.1 FCC (USA) 148
- B.2.4 VCCI (Japan) 149
- B.2.5 BSMI (Taiwan) 149
- NSC2U Server—B 150
- Appendix C: Getting Help 151
- NSC2U Server—C 152
Relacionado con productos y manuales para Hardware De La Computadora Kontron NSC2U IP Network Server
(103 paginas)
(49 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales