Kontron NSW1U IP Network Server Manual de usuario Pagina 83
- Pagina / 110
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Kontron IP Network Server NSW1U
December 2009 Product Guide, rev. 1.4
83
Server Utilities—NSW1U Network Server
The CMOS is now cleared and can be reset by going into the BIOS setup.
6.4 Clearing the Password
If the user or administrator password(s) is lost or forgotten, moving the password clear jumper into
the “clear” position clears both passwords. The password clear jumper must be restored to its original
position before a new password(s) can be set. The password clear jumper (J1H2) is shown in
Figure 10 on page 21.
1. Power down the system and disconnect the power cord.
2. Open the server chassis. See Section 3.2.1, “Removing the Chassis Cover” on page 25 for
instructions.
3. Move the jumper (J1H2) from the normal operation position, Password Clear Protect, at pins 1
and 2 to the Password Clear Erase position, covering pins 2 and 3.
4. Wait 5 seconds.
5. Return the Password Clear jumper (J1H2) to the normal operational position, covering pins 1 and
2.
6. Close the server chassis. See Section 3.2.2, “Installing the Chassis Cover” on page 26 for
instructions.
7. Reconnect the power and restart the system.
6.5 BMC Force Update Procedure
When performing a standard BMC firmware update procedure, the update utility places the BMC into
an update mode to allow the firmware to load safely onto the flash device. In the unlikely event that
the BMC firmware update process fails because the BMC is not in the proper update state, the server
board provides a BMC Force Update jumper that can force the BMC into the proper update state. Use
the following procedure if the standard BMC firmware update process fails.
1. Power down and remove AC Power.
2. Open the server chassis. Open the server. See Section 3.2.1, “Removing the Chassis Cover” on
page 25 for instructions.
3. Put a jumper on the J1E3 header.
4. Close the server chassis.
5. Reconnect the power and restart the system.
6. Perform the standard BMC firmware update procedure as documented in the README.TXT file
included in the BMC Firmware Update package.
7. When the update has finished, power down the system and remove the power cord.
8. Open the server chassis (remove the top cover).
9. Remove the jumper from J1E3.
10. Close the server chassis.
11. Reconnect the power and restart the system.
Note: Normal BMC functionality is disabled when the Force BMC Update jumper is populated.
The server should never be run with the BMC Force Update jumper populated and
should only be used when the standard firmware update process fails. This header
should remain unpopulated when the server is running normally.
- Product Guide 1
- Rev. 1.4 1
- Contents 3
- NSW1U Network Server—Contents 4
- Contents—NSW1U Network Server 5
- Revision History 7
- 1 Introduction 9
- 1.3 Product Accessories 10
- •System drivers 11
- • Firmware and BIOS updates 11
- 2.1 Server Components 14
- 2.2 Back Panel 15
- 2.3 NSW1U Server Front Panels 16
- AF000816rev3 17
- AF000817rev 18
- AF000818 19
- 2.5.1 Front Panel Features 20
- AF000750 21
- 2.8 Hard Disk Drives 22
- 2.9 Riser Card Assembly 22
- 2.10 Power Supply 22
- 2.11 System Cooling 22
- AF000830 23
- 2.12 Hardware Requirements 24
- 3.1 Before You Begin 25
- AF000876rev 26
- AF000875 27
- AF000880 28
- 3.3.1.1 Jumper Blocks 29
- 3.3.1.4 BIOS Select Jumper 30
- DIMM Sockets 32
- 3.3.3.1 Installing DIMMs 34
- AF000775 35
- 19, “A” and “B”) 37
- AF000769 38
- AF000770 38
- AF000773 39
- AF000877 41
- 4.1 Before You Begin 45
- AF000820 48
- TS000407 49
- TS000409 50
- TS000410 51
- TS000411 52
- TS000213 53
- TS000214 54
- 4.5.2 Installing the RMM2 55
- GCM3 ModuleRMM Module 56
- AF000884 57
- AF000887 58
- AF000888 59
- AF000886 60
- TS000504 61
- TS000505 62
- TS000506 62
- TS000507 63
- TS000508 64
- 5.1 Before You Begin 65
- TS000404 66
- TS000405 67
- TS000406 68
- AF000896 69
- AF000897 71
- AF000894 72
- AF000895 72
- AF000898 74
- AF000899 75
- TS000416 77
- TS000417 78
- 5.6.2 Running Setup 79
- 6 Server Utilities 80
- 6.2 Updating the BIOS 81
- Yes] [NO] 81
- 6.2.1.2 Obtaining the Update 82
- 6.3 Clearing the CMOS 82
- 6.4 Clearing the Password 83
- 7 Troubleshooting 84
- 7.5 LED Information 89
- 7.6 BIOS Error Messages 90
- 7.6.1 BIOS POST Beep Codes 91
- Table 11. BMC Beep Codes 92
- 8 Warranty 93
- A.1 Emissions Disclaimer 94
- A.2 Intended Uses 94
- A.3 Safety Cautions 96
- Wichtige Sicherheitshinweise 97
- Consignes de sécurité 99
- B.2.1 FCC (USA) 106
- B.2.4 VCCI (Japan) 107
- B.2.5 BSMI (Taiwan) 107
- B.2.6 Korean RRL Compliance 108
- Appendix C: Getting Help 109
Relacionado con productos y manuales para Hardware De La Computadora Kontron NSW1U IP Network Server
(9 paginas)
(49 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.168 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales