Kontron AT8902M CLI Manual de usuario Pagina 261
- Pagina / 315
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT8902M Management Commands
Page 6 - 9 AT8902M CLI Reference Manual
6.3.6 session-timeout
This command sets the Telnet session timeout value.The timeout value unit of time is
minutes. A value of 0 indicates that a session remains active indefinitely.
Default 0
Format session-timeout <0-160>
Mode Line Config
6.3.6.1 no session-timeout
This command sets the Telnet session timeout value to the default. The timeout value
unit of time is minutes.
Format no session-timeout
Mode Line Config
6.3.7 telnetcon maxsessions
This command specifies the maximum number of Telnet connection sessions that can
be established. A value of 0 indicates that no Telnet connection can be established. The
range is 0-5.
Default 5
Format telnetcon maxsessions <0-5>
Mode Privileged EXEC
6.3.7.1 no telnetcon maxsessions
This command sets the maximum number of Telnet connection sessions that can be
established to the default value.
Format no telnetcon maxsessions
Mode Privileged EXEC
6.3.8 telnetcon timeout
This command sets the Telnet connection session timeout value, in minutes. A session
is active as long as the session has not been idle for the value set. The time is a decimal
value from 1 to 160.
NOTE: When you change the timeout value, the new value is applied to all
active and inactive sessions immediately. Any sessions that have been
idle longer than the new timeout value are disconnected immediately.
Default 5
Format telnetcon timeout <1-160>
Mode Privileged EXEC
6.3.8.1 no telnetcon timeout
This command sets the Telnet connection session timeout value to the default.
- AT8902M CLI Reference Manual 1
- AdvancedTCA 1
- AT8902M Preface 2
- Table of Contents 3
- Table of Contents AT8902M 10
- AT8902M Table of Contents 11
- Appendix 19
- Preface AT8902M 22
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.2.1 Common Parameter Values 29
- 1.5 Command Modes 31
- 1.5.2 CLI Error Messages 34
- 1.6 Using CLI Help 35
- 1.7 Accessing the CLI 36
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8902M 100
- AT8902M Switching Commands 101
- Routing Commands 115
- Chapter 1 115
- 3. Routing Commands 116
- AT8902M Routing Commands 117
- Routing Commands AT8902M 118
- Quality of Service Commands 169
- 4.1.3 classofservice trust 171
- [<slot/port>] 174
- 4.2.1 diffserv 175
- 4.3 DiffServ Class Commands 176
- 4.3.2 class-map rename 177
- 4.3.3 match ethertype 177
- 4.3.4 match any 177
- 4.3.5 match class-map 177
- 4.3.5.1 no match class-map 178
- 4.3.6 match cos 178
- 4.3.7 match secondary-cos 178
- 4.3.9 match dstip 179
- 4.3.10 match dstl4port 179
- 4.3.11 match ip dscp 179
- 4.3.12 match ip precedence 179
- 4.3.13 match ip tos 180
- 4.3.14 match protocol 180
- 4.3.16 match srcip 181
- 4.3.17 match srcl4port 181
- 4.3.18 match vlan 181
- 4.4 DiffServ Policy Commands 182
- 4.4.2 drop 183
- 4.4.3 mirror 183
- 4.4.4 redirect 183
- 4.4.5 conform-color 183
- 4.4.6 class 183
- 4.4.6.1 no class 184
- 4.4.7 mark cos 184
- 4.4.8 mark ip-dscp 184
- 4.4.9 mark ip-precedence 184
- 4.4.10 police-simple 185
- 4.4.11 policy-map 185
- 4.4.11.1 no policy-map 185
- 4.5 DiffServ Service Commands 186
- 4.6 DiffServ Show Commands 187
- 4.6.2 show diffserv 188
- 4.6.3 show policy-map 188
- 4.6.4 show diffserv service 190
- 4.6.7 show service-policy 191
- 4.7.3 {deny 192
- 4.7.4 mac access-group 194
- 4.7.4.1 no mac access-group 194
- 4.7.5 show mac access-lists 194
- 4.8.1 access-list 195
- 4.8.1.1 no access-list 196
- 4.8.2 ip access-group 197
- 4.8.2.1 no ip access-group 197
- 4.8.3 acl-trapflags 197
- 4.8.3.1 no acl-trapflags 197
- 4.8.4 show ip access-lists 197
- 4.8.5 show access-lists 198
- 4.9 ACL trap commands 199
- Utility Commands 201
- 5. Utility Commands 202
- AT8902M Utility Commands 203
- Utility Commands AT8902M 204
- Management Commands 253
- 6. Management Commands 254
- AT8902M Management Commands 255
- Management Commands AT8902M 256
- Getting Help 289
- A. Getting Help 290
- AT8902M Getting Help 291
- Getting Help AT8902M 292
- (if not under warranty) 293
- List of Commands 295
- B. List of Commands 296
- AT8902M List of Commands 297
- List of Commands AT8902M 298
Relacionado con productos y manuales para Hardware Kontron AT8902M CLI
Hardware Kontron AT8904 Manual de usuario
(93 paginas)
(93 paginas)
Hardware Kontron AT8904 CLI Manual de usuario
(317 paginas)
(317 paginas)
Hardware Kontron AT8940 Manual de usuario
(84 paginas)
(84 paginas)
Hardware Kontron RTM8940 Manual de usuario
(36 paginas)
(36 paginas)
Hardware Kontron AT8402 CLI Manual de usuario
(253 paginas)
(253 paginas)
Hardware Kontron AT8404 Manual de usuario
(132 paginas)
(132 paginas)
Hardware Kontron AT8404 CLI Manual de usuario
(373 paginas)
(373 paginas)
Hardware Kontron RTM8050 Manual de usuario
(37 paginas)
(37 paginas)
Hardware Kontron AT8050 Manual de usuario
(165 paginas)
(165 paginas)
Hardware Kontron RTM8242 Manual de usuario
(34 paginas)
(34 paginas)
Hardware Kontron AT8242 Manual de usuario
(109 paginas)
(109 paginas)
Hardware Kontron AT8060 Manual de usuario
(160 paginas)
(160 paginas)
Hardware Kontron RTM806x Manual de usuario
(40 paginas)
(40 paginas)
Hardware Kontron 820152 DC-DC Manual de usuario
(4 paginas)
(4 paginas)
Hardware Kontron 820153 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
Hardware Kontron 820155 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales