Kontron AT8902M CLI Manual de usuario Pagina 221
- Pagina / 315
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
AT8902M Utility Commands
Page 5 - 21 AT8902M CLI Reference Manual
Mode Global Config
5.4.3.1 no logging cli-command
This command disables the CLI command Logging feature.
Format
no logging cli-command
Mode Global Config
5.4.4 logging console
This command enables logging to the console. You can specify the <severitylevel>
value as either an integer from 0 to 7 or symbolically through one of the following
keywords:
emergency (0), alert (1), critical (2), error (3), warning (4), notice
(5),
info (6), or debug (7).
Default
disabled; critical when enabled
Format logging console [severitylevel]
Mode Global Config
5.4.4.1 no logging console
This command disables logging to the console.
Format
no logging console
Mode Global Config
5.4.5 logging host
This command enables logging to a host. You can configure up to eight hosts. The
<ipaddr> is the IP address of the logging host. The <port> value is a port number from
1 to 65535. You can specify the
<severitylevel> value as either an integer from 0 to
7 or symbolically through one of the following keywords:
emergency (0), alert (1),
critical (2), error (3), warning (4), notice (5), info (6), or debug (7).
Default
port—514
level—critical (2)
Format logging host <ipaddr> [<port>][<severitylevel>]
Mode Global Config
5.4.6 logging host remove
This command disables logging to host. See 5.4.11 “show logging hosts” on page 5 -
23 for a list of host indexes.
Format
logging host remove <hostindex>
Mode Global Config
5.4.7 logging port
This command sets the local port number of the LOG client for logging messages. The
<portid> can be in the range from 1 to 65535.
- AT8902M CLI Reference Manual 1
- AdvancedTCA 1
- AT8902M Preface 2
- Table of Contents 3
- Table of Contents AT8902M 10
- AT8902M Table of Contents 11
- Appendix 19
- Preface AT8902M 22
- 1.1 Command Syntax 28
- 1.2 Command Conventions 28
- 1.2.1 Common Parameter Values 29
- 1.5 Command Modes 31
- 1.5.2 CLI Error Messages 34
- 1.6 Using CLI Help 35
- 1.7 Accessing the CLI 36
- Switching Commands 37
- 2. Switching Commands 38
- Switching Commands AT8902M 100
- AT8902M Switching Commands 101
- Routing Commands 115
- Chapter 1 115
- 3. Routing Commands 116
- AT8902M Routing Commands 117
- Routing Commands AT8902M 118
- Quality of Service Commands 169
- 4.1.3 classofservice trust 171
- [<slot/port>] 174
- 4.2.1 diffserv 175
- 4.3 DiffServ Class Commands 176
- 4.3.2 class-map rename 177
- 4.3.3 match ethertype 177
- 4.3.4 match any 177
- 4.3.5 match class-map 177
- 4.3.5.1 no match class-map 178
- 4.3.6 match cos 178
- 4.3.7 match secondary-cos 178
- 4.3.9 match dstip 179
- 4.3.10 match dstl4port 179
- 4.3.11 match ip dscp 179
- 4.3.12 match ip precedence 179
- 4.3.13 match ip tos 180
- 4.3.14 match protocol 180
- 4.3.16 match srcip 181
- 4.3.17 match srcl4port 181
- 4.3.18 match vlan 181
- 4.4 DiffServ Policy Commands 182
- 4.4.2 drop 183
- 4.4.3 mirror 183
- 4.4.4 redirect 183
- 4.4.5 conform-color 183
- 4.4.6 class 183
- 4.4.6.1 no class 184
- 4.4.7 mark cos 184
- 4.4.8 mark ip-dscp 184
- 4.4.9 mark ip-precedence 184
- 4.4.10 police-simple 185
- 4.4.11 policy-map 185
- 4.4.11.1 no policy-map 185
- 4.5 DiffServ Service Commands 186
- 4.6 DiffServ Show Commands 187
- 4.6.2 show diffserv 188
- 4.6.3 show policy-map 188
- 4.6.4 show diffserv service 190
- 4.6.7 show service-policy 191
- 4.7.3 {deny 192
- 4.7.4 mac access-group 194
- 4.7.4.1 no mac access-group 194
- 4.7.5 show mac access-lists 194
- 4.8.1 access-list 195
- 4.8.1.1 no access-list 196
- 4.8.2 ip access-group 197
- 4.8.2.1 no ip access-group 197
- 4.8.3 acl-trapflags 197
- 4.8.3.1 no acl-trapflags 197
- 4.8.4 show ip access-lists 197
- 4.8.5 show access-lists 198
- 4.9 ACL trap commands 199
- Utility Commands 201
- 5. Utility Commands 202
- AT8902M Utility Commands 203
- Utility Commands AT8902M 204
- Management Commands 253
- 6. Management Commands 254
- AT8902M Management Commands 255
- Management Commands AT8902M 256
- Getting Help 289
- A. Getting Help 290
- AT8902M Getting Help 291
- Getting Help AT8902M 292
- (if not under warranty) 293
- List of Commands 295
- B. List of Commands 296
- AT8902M List of Commands 297
- List of Commands AT8902M 298
Relacionado con productos y manuales para Hardware Kontron AT8902M CLI
Hardware Kontron AT8904 Manual de usuario
(93 paginas)
(93 paginas)
Hardware Kontron AT8904 CLI Manual de usuario
(317 paginas)
(317 paginas)
Hardware Kontron AT8940 Manual de usuario
(84 paginas)
(84 paginas)
Hardware Kontron RTM8940 Manual de usuario
(36 paginas)
(36 paginas)
Hardware Kontron AT8402 CLI Manual de usuario
(253 paginas)
(253 paginas)
Hardware Kontron AT8404 Manual de usuario
(132 paginas)
(132 paginas)
Hardware Kontron AT8404 CLI Manual de usuario
(373 paginas)
(373 paginas)
Hardware Kontron RTM8050 Manual de usuario
(37 paginas)
(37 paginas)
Hardware Kontron AT8050 Manual de usuario
(165 paginas)
(165 paginas)
Hardware Kontron RTM8242 Manual de usuario
(34 paginas)
(34 paginas)
Hardware Kontron AT8242 Manual de usuario
(109 paginas)
(109 paginas)
Hardware Kontron AT8060 Manual de usuario
(160 paginas)
(160 paginas)
Hardware Kontron RTM806x Manual de usuario
(40 paginas)
(40 paginas)
Hardware Kontron 820152 DC-DC Manual de usuario
(4 paginas)
(4 paginas)
Hardware Kontron 820153 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
Hardware Kontron 820155 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.081 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales