Kontron COMe-bHL6 Manual de usuario Pagina 67
- Pagina / 129
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
COMe-bHL6 / Pinout List
7.2 Connector X1A Row A
Pin Signal Description Type Termination Comment
A1 GND Power Ground PWR GND - -
A2 GBE0_MDI3- Ethernet Media Dependent Interface 3 - DP-I/O - -
A3 GBE0_MDI3+ Ethernet Media Dependent Interface 3 + DP-I/O - -
A4 GBE0_LINK100# Ethernet 100 Mbit Link Indicator OD - -
A5 GBE0_LINK1000# Ethernet 1000 Mbit Link Indicator OD - -
A6 GBE0_MDI2- Ethernet Media Dependent Interface 2 - DP-I/O - -
A7 GBE0_MDI2+ Ethernet Media Dependent Interface 2 + DP-I/O - -
A8 GBE0_LINK# Ethernet Link Indicator OD - -
A9 GBE0_MDI1- Ethernet Media Dependent Interface 1 - DP-I/O - -
A10 GBE0_MDI1+ Ethernet Media Dependent Interface 1 + DP-I/O - -
A11 GND Power Ground PWR GND - -
A12 GBE0_MDI0- Ethernet Media Dependent Interface 0 - DP-I/O - -
A13 GBE0_MDI0+ Ethernet Media Dependent Interface 0 + DP-I/O - -
A14 GBE0_CTREF Center Tab Reference Voltage O - 1µF capacitor to GND
A15 SUS_S3# Suspend To RAM (or deeper) Indicator O-3.3 PD 10k -
A16 SATA0_TX+ SATA 0 Transmit Pair + DP-O - -
A17 SATA0_TX- SATA 0 Transmit Pair - DP-O - -
A18 SUS_S4# Suspend To Disk (or deeper) Indicator O-3.3 - -
A19 SATA0_RX+ SATA 0 Receive Pair + DP-I - -
A20 SATA0_RX- SATA 0 Receive Pair - DP-I - -
A21 GND Power Ground PWR GND - -
A22 SATA2_TX+ SATA 2 Transmit Pair + DP-O - -
A23 SATA2_TX- SATA 2 Transmit Pair - DP-O - -
A24 SUS_S5# Soft Off Indicator O-3.3 - -
A25 SATA2_RX+ SATA 2 Receive Pair + DP-I - -
A26 SATA2_RX- SATA 2 Receive Pair - DP-I - -
A27 BATLOW# Battery Low I-3.3 PU 10k 3.3V (S5) assertion will prevent wake from S3-S5 state
A28 (S)ATA_ACT# Serial ATA LED OD-3.3 PU 10k 3.3V (S0) can pull down 3mA
A29 AC/HDA_SYnc HD Audio Sync O-3.3 PD 15k in PCH resistor value can range from 9kOhm to 50kOhm
A30 AC/HDA_RST# HD Audio Reset O-3.3 - -
A31 GND Power Ground PWR GND - -
A32 AC/HDA_BITCLK HD Audio Bit Clock Output O-3.3 - -
A33 AC/HDA_SDOUT HD Audio Serial Data Out O-3.3 PD 15k in PCH resistor value can range from 9kOhm to 50kOhm
A34 BIOS_DIS0# BIOS Selection Strap 0 I-3.3 PU 10k 3.3V (SPI) PU might be powered during suspend
A35 THRMTRIP# Thermal Trip O-3.3 PU 10k 3.3V (S0) do not use for overtemperatur detection (because this
signal is a S0 signal, it's not possible to see if module
shuts down regular or caused by CPU overtemperatur)
A36 USB6- USB 2.0 Data Pair Port 6 – DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A37 USB6+ USB 2.0 Data Pair Port 6 + DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A38 USB_6_7_OC# USB Overcurrent Indicator Port 6/7 I-3.3 PU 10k 3.3V (S5) -
A39 USB4- USB 2.0 Data Pair Port 4 - DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A40 USB4+ USB 2.0 Data Pair Port 4 + DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A41 GND Power Ground PWR GND - -
A42 USB2- USB 2.0 Data Pair Port 2 – DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A43 USB2+ USB 2.0 Data Pair Port 2 + DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A44 USB_2_3_OC# USB Overcurrent Indicator Port 2/3 I-3.3 PU 10k 3.3V (S5) -
A45 USB0- USB 2.0 Data Pair Port 0 – DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A46 USB0+ USB 2.0 Data Pair Port 0 + DP-I/O PD 15k in PCH resistor value can range from 14kOhm to 25kOhm
A47 VCC_RTC Real-Time Clock Circuit Power Input PWR 3V - -
A48 EXCD0_PERST# Express Card Reset Port 0 O-3.3 - -
A49 EXCD0_CPPE# Express Card Capable Card Request Port 0 I-3.3 PU 10k 3.3V (S0) -
A50 LPC_SERIRQ Serial Interrupt Request I/OD-3.3 PU 8k25 3.3V (S0) -
A51 GND Power Ground PWR GND - -
A52 PCIE_TX5+ PCI Express Lane 5 Transmit + DP-O - -
A53 PCIE_TX5- PCI Express Lane 5 Transmit - DP-O - -
A54 GPI0 General Purpose Input 0 I-3.3 PU 10k 3.3V (S0) -
A55 PCIE_TX4+ PCI Express Lane 4 Transmit + DP-O - -
A56 PCIE_TX4- PCI Express Lane 4 Transmit - DP-O - -
A57 GND Power Ground PWR GND - -
A58 PCIE_TX3+ PCI Express Lane 3 Transmit + DP-O - -
A59 PCIE_TX3- PCI Express Lane 3 Transmit - DP-O - -
A60 GND Power Ground PWR GND - -
A61 PCIE_TX2+ PCI Express Lane 2 Transmit + DP-O - -
A62 PCIE_TX2- PCI Express Lane 2 Transmit - DP-O - -
67
- COMe-bHL6 1
- » Table of Contents « 3
- 1 User Information 6
- 1.5 Warranty 7
- 1.6 Technical Support 7
- 2 Introduction 8
- COMe-bHL6 / Introduction 9
- 2.5 COM Express® Benefits 10
- 3 Product Specification 11
- 3.2 Functional Specification 12
- CPU Features 14
- PCH comparison 16
- Graphics Core 17
- PEG Configuration 18
- Connectivity 19
- Misc Interfaces and Features 19
- Kontron Features 20
- Additional features 20
- Power Features 20
- 3.3 Block Diagram 21
- 3.4 Accessories 22
- 3.5 Electrical Specification 23
- 3.5.5 ATX Mode 24
- 3.5.6 Single Supply Mode 24
- 3.6 Power Control 25
- 3.7.2 Humidity 26
- WEEE Directive 27
- Conformal Coating 27
- Shock & Vibration 28
- 3.9 MTBF 29
- 3.10 Mechanical Specification 30
- 3.11 Module Dimensions 31
- 3.13 Onboard Connectors 33
- 4 Features and Interfaces 35
- 4.2 Rapid Shutdown 36
- 4.5 SPI boot 39
- Using an external SPI flash 40
- 4.6 M.A.R.S 41
- 4.7 UART 42
- 4.8 Fast I2C 43
- Time-out events 44
- WDT Signal 44
- 4.11 Speedstep Technology 47
- 4.12 C-States 48
- 4.13 Hyper Threading 49
- 4.15 VID-x 51
- 4.17 Display Configuration 53
- 3 independent Display Support 54
- DDI Design Consideration 55
- DVI-I Design Topology 55
- Requirements 56
- Setup a Multi-monitor system 56
- 4.19 Intel® Wireless Display 57
- 4.20 Intel® vPro™ technology 59
- 5 System Resources 61
- 5.2 Memory Area 62
- 5.3 I/O Address Map 62
- 5.5 Internal I2C Bus 63
- 5.6 External I2C Bus 63
- 6 Connectors 65
- 7 Pinout List 66
- 7.2 Connector X1A Row A 67
- COMe-bHL6 / Pinout List 68
- 7.3 Connector X1A Row B 69
- 7.4 Connector X1B Row C 71
- 7.5 Connector X1B Row D 73
- 8 BIOS Operation 75
- 8.5 BIOS Setup 76
- System Information 78
- Boot Features 79
- Network Stack 81
- Platform Information 82
- 8.5.2 Advanced 83
- Silicon Information 84
- Processor Configuration 85
- Processor Power Management 86
- Miscellaneous 88
- I2C Speed 89
- Watchdog 90
- Generic LPC Decode Ranges 91
- H/W Monitor 92
- HDD Configuration 94
- Memory Configuration 96
- Graphics Configuration 99
- COMe-bHL6 / BIOS Operation 100
- IGD Configuration 101
- PEG Port Configuration 103
- South Bridge Configuration 105
- SB PCI Express Config 106
- SB USB Config 108
- SB Azalia Config 109
- Network Configuration 110
- CPLD Configuration 111
- LPC SIO Configuration 112
- ME Configuration (default) 115
- Thermal Configuration 117
- CPU Thermal Configuration 118
- Passive Cooling 120
- ICC Configuration 121
- Intel® Rapid Start Technology 123
- 8.5.3 Security 125
- Security 126
- 8.5.4 Boot 127
- 8.5.5 Exit 128
- Corporate Offices 129
Relacionado con productos y manuales para Hardware Kontron COMe-bHL6
Hardware Kontron COMe-bIP6 Manual de usuario
(133 paginas)
(133 paginas)
Hardware Kontron COMe-bIP2 Manual de usuario
(128 paginas)
(128 paginas)
Hardware Kontron COMe-bSC2 Manual de usuario
(125 paginas)
(125 paginas)
Hardware Kontron COMe-bSC6 Manual de usuario
(117 paginas)
(117 paginas)
Hardware Kontron ETXexpress-AI Manual de usuario
(129 paginas)
(129 paginas)
Hardware Kontron COMe-bPC2 Manual de usuario
(115 paginas)
(115 paginas)
Hardware Kontron COMe-bCD2 Manual de usuario
(80 paginas)
(80 paginas)
Hardware Kontron COMe-bP5020 Manual de usuario
(71 paginas)
(71 paginas)
Hardware Kontron COMe-cP2020 Manual de usuario
(106 paginas)
(106 paginas)
Hardware Kontron COMe-mSP1 Manual de usuario
(97 paginas)
(97 paginas)
Hardware Kontron COMe-mTT10 Manual de usuario
(94 paginas)
(94 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.125 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales