Kontron COMe-bIP2 Manual de usuario Pagina 51
- Pagina / 128
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
COMe-bIP2 / Features and Interfaces
eDP - embedded Display Port
Intel® 6 & 7-Series Chipset based Computer-on-modules support the embedded Display Port shared on Digital Display
Interface DDI3. To enable the eDP, LVDS must be switched off by hardware strap option. This feature is implemented in
COMe-bSC2 (starting with hardware revision CE 2.x.x) and COMe-bIP2/6 by external strap option on the carrier board. The
General Purpose Input GPI3 (COM Express Pin A85) is pulled-up with 10kOhm on the module. Leaving GPI3 open on the
baseboard enables LVDS (default configuration). To enable the eDP instead of LVDS, GPI3 must be pulled-down with a
resistor ≤1kOhm or tied directly to GND during boot-up.
The GPIO should not be used during boot-up until CB_RESET# becomes inactive
Digital Display Interface Features
The integrated Intel® GMA HD4000 (Gen7) graphics supports:
» High-bandwidth Digital Content Protection (HDCP) on HDMI and DisplayPort with up to 2 HDCP streams
simultaneously
» One active Protected Audio and Video Path (PAVP) session on HDMI or DisplayPort
» Dual Stream DP/HDMI Audio if activated in BIOS (See BIOS Chapter HDAudio Configuration) and O/S (HDMI codec
DDI enabled)
» DP/HDMI/DVI Hot-plug (low-active)
Supported Audio Formats on HDMI and DisplayPort
Audio Formats HDMI DisplayPort
AC-3 Dolby Digital YES NO
Dolby Digital Plus YES NO
DTS-HD YES NO
LPCM, 192kHz/24bit, 8 channel YES YES (Up to 2 channel 96kHz, 24bit)
Dolby True HD, DTS HD Master Audio YES NO
51
- COMe-bIP2 1
- » Table of Contents « 3
- 1 User Information 6
- 1.5 Warranty 7
- 1.6 Technical Support 7
- 2 Introduction 8
- 2.5 COM Express® Benefits 9
- 3 Product Specification 10
- 3.2 Functional Specification 11
- PCH comparison 14
- Graphics Core 15
- Connectivity 16
- Misc Interfaces and Features 17
- Kontron Features 17
- Additional features 17
- Power Features 17
- 3.3 Block Diagram 18
- 3.4 Accessories 19
- 3.5 Electrical Specification 20
- 3.5.5 ATX Mode 21
- 3.5.6 Single Supply Mode 21
- 3.6 Power Control 22
- 3.7.2 Humidity 23
- WEEE Directive 24
- Conformal Coating 24
- Shock & Vibration 25
- 3.9 MTBF 26
- 3.10 Mechanical Specification 27
- 3.11 Module Dimensions 28
- 3.13 Onboard Fan Connector 30
- 4 Features and Interfaces 31
- 4.4 SPI boot 33
- Using an external SPI flash 34
- 4.5 M.A.R.S 35
- 4.6 Fast I2C 36
- Configuration 37
- Time-out events 38
- WDT Signal 38
- 4.10 Speedstep Technology 41
- 4.11 C-States 42
- 4.12 Hyper Threading 43
- 4.14 VID-x 45
- 4.17 Display Configuration 49
- DDI Design Consideration 52
- DVI-I Design Topology 52
- 3 independent Display Support 52
- Requirements 53
- Setup a Multi-monitor system 53
- 4.19 Intel® vPro™ technology 54
- 5 System Resources 56
- 5.2 Memory Area 57
- 5.3 I/O Address Map 57
- 5.5 I2C Bus 58
- 5.6 JILI I2C Bus 58
- 5.7 SDVO I2C Bus 58
- 6 Connectors 60
- 7 Pinout List 61
- 7.2 Connector X1A Row A 62
- COMe-bIP2 / Pinout List 63
- 7.3 Connector X1A Row B 64
- 7.4 Connector X1B Row C 66
- 7.5 Connector X1B Row D 68
- 8 BIOS Operation 70
- 8.3 Setup Guide 72
- 8.4 POST Codes 72
- Item Specific Help Window 73
- General Help Window 73
- 8.5 BIOS Setup 74
- Platform Information 75
- 8.5.2 Advanced 76
- PCI Subsystem Settings 77
- ACPI Settings 78
- Trusted Computing 79
- CPU Configuration 80
- CPU Information 81
- Miscellaneous 82
- Onboard I2C Bus Configuration 83
- Watchdog 84
- Smart Battery Configuration 85
- Battery Information 86
- Generic LPC Decode Ranges 87
- Thermal Configuration 88
- Passive Cooling 89
- Intel Fast Flash Standby 90
- PCH-FW Configuration 91
- Firmware Update Configuration 93
- Super IO Configuration 95
- Serial Port 1 Configuration 96
- Serial Port 2 Configuration 97
- Parallel Port Configuration 98
- H/W Monitor 99
- COMe-bIP2 / BIOS Operation 100
- Console Redirection Settings 102
- Intel ICC 103
- Clock Spread Spectrum 104
- CPU PPM Configuration 105
- 8.5.3 Chipset 106
- PCH-IO Configuration 107
- LAN Configuration 108
- SATA Configuration 109
- HDA Configuration 111
- USB Configuration 112
- PCI Express Configuration 113
- SystemAgent Configuration 115
- Graphics Configuration 116
- LCD Control 117
- - DVI-I' 118
- Memory Configuration 120
- Custom Memory Profile Control 121
- GT - Power Management Control 122
- 8.5.4 Boot 123
- Boot Option Priority 124
- 8.5.5 Security 125
- Set HDD Password 126
- 8.5.6 Save & Exit 127
- Corporate Offices 128
Relacionado con productos y manuales para Hardware Kontron COMe-bIP2
Hardware Kontron COMe-bSC2 Manual de usuario
(125 paginas)
(125 paginas)
Hardware Kontron COMe-bSC6 Manual de usuario
(117 paginas)
(117 paginas)
Hardware Kontron ETXexpress-AI Manual de usuario
(129 paginas)
(129 paginas)
Hardware Kontron COMe-bPC2 Manual de usuario
(115 paginas)
(115 paginas)
Hardware Kontron COMe-bCD2 Manual de usuario
(80 paginas)
(80 paginas)
Hardware Kontron COMe-bP5020 Manual de usuario
(71 paginas)
(71 paginas)
Hardware Kontron COMe-cP2020 Manual de usuario
(106 paginas)
(106 paginas)
Hardware Kontron COMe-mSP1 Manual de usuario
(97 paginas)
(97 paginas)
Hardware Kontron COMe-mTT10 Manual de usuario
(94 paginas)
(94 paginas)
Hardware Kontron COMe-mCT10 Manual de usuario
(100 paginas)
(100 paginas)
Hardware Kontron COMe-mBT10 Manual de usuario
(87 paginas)
(87 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales