Kontron AT8242 Manual de usuario Pagina 31
- Pagina / 109
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
15 AT8242
www.kontron.com
2.9 Redundant IPMC Firmware & BootBlock
The IPMC runs a firmware from SPI flash memory. The IPMC Boot Block saves the last two copies of the IPMC
firmware image, manages bank states and can rollback to the previous firmware image in flash in case of
update problem.
2.10 LEDs Description
The following table lists the LED on the faceplate (not counting the RJ-45 Ethernet LED).
Table 2-4:Faceplate LEDs
2.10.1 Hot Swap LED (LED0)
The Blue / Hot Swap LED indicates the hot swap status of the unit. The LED is ON when it is safe to remove the
unit from the slot. During normal operation, this LED is OFF.
Solid On (100 % on): FRU Inactive
Long Blink ( 90 % on): FRU Activation Request
Solid Off ( 0 % on): FRU Activation In Progress / FRU Active
Short Blink ( 10 % on): FRU Deactivation Request / FRU Deactivation In Progress
2.10.2 Out Of Service (LED1)
The AdvancedTCA LED1 is red or amber and indicates an Out-of-Service (OOS) condition. During normal
operation, the OOS LED is OFF. This LED is ON when IPMC is in reset or starting up, and is user configurable if
needed by a customer application.
Solid On: IPMC in reset or starting up
Note:
The IPMC has an external hardware watchdog.
LED Name Color Controlled by Description
ATCA0 Blue IPMC Blade Hot Swap status
ATCA1 Amber/Red IPMC Blade OOS (out-of-service)
ATCA2 Amber/Green IPMC Healthy status
User LED Amber/Green IPMC User LED
- » Kontron User's Guide « 1
- Revision History 2
- Customer Service 2
- Table of Contents 3
- List of Figures 7
- List of Tables 8
- Safety Instructions 10
- How to Use This Guide 12
- Customer Comments 13
- Advisory Conventions 13
- Unpacking 14
- Powering Up the System 14
- Adapter Cables 14
- Storing Boards 14
- Safety Certification 15
- CE Certification 15
- Limited Warranty 16
- Product Description 17
- 1. Product Description 18
- 1.3 Board Specifications 19
- 1.4 Compliance 21
- 1.5 Hot-Plug Capability 21
- Board Features 23
- 2. Board Features 24
- 2.2 Network Processors 25
- 2.3 Unit Computer 25
- 2.4 Switch 25
- 2.4.2 Base Interface 26
- 2.4.3 Fabric Interface 26
- 11 AT8242 27
- 12 AT8242 28
- 2.5 Serial Interfaces 29
- 2.6 Serial-Over-LAN (SOL) 30
- 2.7 Web Interface 30
- 2.8 FPGA 30
- 2.10 LEDs Description 31
- 2.10.3 Healthy LED (LED2) 32
- 2.10.4 User LED (LED3) 32
- Figure 2-2:Faceplate LEDs 33
- Installing the Board 34
- 3. Installing the Board 35
- 20 AT8242 36
- 3.3.2 Installing Memory 37
- 22 AT8242 38
- 3.5.2 Removing the Board 39
- 3.5.3 Installing the RTM 39
- 3.5.4 Removing the RTM 40
- Hardware Management 41
- 4. Hardware Management 42
- 4.2.2 IPMC specific features 43
- 28 AT8242 44
- 4.2.3.2 System 45
- 4.2.3.3 Sensor 45
- 4.2.3.4 Event Log 45
- 4.2.4 Control 46
- 4.2.5 Maintenance 46
- 4.3 IPMC 47
- 32 AT8242 48
- 33 AT8242 49
- 34 AT8242 50
- 35 AT8242 51
- 36 AT8242 52
- 37 AT8242 53
- Table 4-15:SOL Commands 54
- Table 4-17:HPM Commands 55
- 4.3.2 Sensor Data Records 56
- 4.3.2.1 IPMC Sensors 57
- 42 AT8242 58
- 43 AT8242 59
- 44 AT8242 60
- 45 AT8242 61
- 46 AT8242 62
- 4.3.3 FRU Information 63
- 48 AT8242 64
- 49 AT8242 65
- 50 AT8242 66
- 4.4 Virtual MMC 67
- 52 AT8242 68
- 53 AT8242 69
- 54 AT8242 70
- 55 AT8242 71
- 56 AT8242 72
- 57 AT8242 73
- 58 AT8242 74
- 59 AT8242 75
- 4.4.2 MMC sensors 76
- 61 AT8242 77
- 62 AT8242 78
- 4.4.4 FRU Information 79
- 4.5 OEM Sensor Tables 80
- 65 AT8242 81
- Table 4-51:POST Value sensor 82
- Table 4-52:Diag Status sensor 82
- Table 4-57:Board Reset sensor 83
- Table 4-58:Power State sensor 84
- Software Setup 85
- 5. Software Setup 86
- 71 AT8242 87
- 72 AT8242 88
- 73 AT8242 89
- 5.1.2.1 Installation 90
- 5.1.3 Embedded Linux 91
- RXAUI/QLM0 xaui0, xaui1 92
- DXAUI/QLM2 xaui2 92
- XAUI/QLM4 xaui3 92
- 77 AT8242 93
- 6. Thermal Considerations 95
- 80 AT8242 96
- 6.1.3 Airflow blockers 97
- 6.1.4 System Airflow 97
- 6.1.5 Thermal Profile 98
- 83 AT8242 99
- Thermal Considerations 100
- 84 AT8242 100
- A. Connector Pinouts 101
- B. Software Update 102
- B.2.3 Firmware Recovery Mode 103
- # run boot_user 104
- C. Getting Help 105
- C.2 When Returning a Unit 106
- D. Glossary 107
- D-2 AT8242 108
- D-3 AT8242 109
Relacionado con productos y manuales para Hardware Kontron AT8242
Hardware Kontron AT8060 Manual de usuario
(160 paginas)
(160 paginas)
Hardware Kontron RTM806x Manual de usuario
(40 paginas)
(40 paginas)
Hardware Kontron 820152 DC-DC Manual de usuario
(4 paginas)
(4 paginas)
Hardware Kontron 820153 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
Hardware Kontron 820155 DC-DC Manual de usuario
(9 paginas)
(9 paginas)
Hardware Kontron KT965 Series Manual de usuario
(90 paginas)
(90 paginas)
Hardware Kontron KTGM45-mITX Manual de usuario
(101 paginas)
(101 paginas)
Hardware Kontron KTQ45-FLEX Manual de usuario
(92 paginas)
(92 paginas)
Hardware Kontron KTQM67-mITX Manual de usuario
(148 paginas)
(148 paginas)
Hardware Kontron KTQ67-FLEX Manual de usuario
(137 paginas)
(137 paginas)
Hardware Kontron KTQ67-FLEX MED Manual de usuario
(129 paginas)
(129 paginas)
Hardware Kontron KTQ77-FLEX Manual de usuario
(141 paginas)
(141 paginas)
Hardware Kontron KTA75-FLEX Manual de usuario
(90 paginas)
(90 paginas)
Hardware Kontron KTH81-mITX Manual de usuario
(98 paginas)
(98 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales